From alenhoff@yahoo.com Wed Nov 13 16:44:23 2002
Subject:Re: CX-3 Update has added wind noise on Leslie sim?!

David:

Just wondering: What's your setup downstream of the CX-3 (pre-amp?
Amp or Leslie, etc.) Going straight to an amp, I find the noise can
be a real distraction unless I pump up the master volume.

Alan

--- In CloneWheel@y..., "David Jacques" wrote:
> Yes, I hear it. But it does not bother me.
>
> -----Original Message-----
> From: Alan Lenhoff [mailto:alenhoff@y...]
> Sent: Wednesday, November 13, 2002 11:23 AM
> To: CloneWheel@y...
> Subject: Re: [CWSG] CX-3 Update has added wind noise on Leslie
sim?!
>
> Just got CX-3 V. 2 software and I also hear the annoying "wind"
noise
> described below when nothing is being played. (Never heard this
with
> Version 1, by the way.) I hear it even on patches in which
> the "noise" parameter is set to 0 (although it's much louder when
the
> noise parameter is set higher).
>
> I've been able to mostly eliminate it by turning my amplifier down
(5
> or lower seems to work), and then turning the master volume on the
> organ all the way up. That works for most purposes, but if I need
to
> set the amp higher (especially on some of the quieter patches),
then
> I must turn the amp higher, and the noise returns.
>
> I'm not using a pre-amp. Could the above be occurring because the
CX-
> 3 generates a particularly weak output signal? My vintage CX-3 is
> MUCH louder at any given amp setting.
>
> Anyone else hearing this sound? Would be interested to know
whether
> only those of us without preamps hear it.
>
> Alan
>
> --- In CloneWheel@y..., "honod3k" wrote:
> > --- In CloneWheel@y..., "jerrythek2000" wrote:
> > > Errr... There was/is no specific white noise element added to
the
> > > Leslie Sim.
> > >
> > > There is a new standing state noise parameter that was added,
> > > which we used very sparingly in some of the voicing. Look for
it
> > > under the 1 button, to the right a number of ticks. If you
have
> > this
> > > "up" then you'll get that sound. Just set it back to 00.
> > >
> > > The new Speaker Simulator parameter is a switch to turn OFF
> > > the simulator which has always been there. By turning it OFF
> > > you're turning off a sophisticated bank of EQ/filters and
you'll
> > get
> > > a very different, and perhaps more "open" tonality.
> > >
> > > But again, nothing to do with a perceived white noise
parameter
> > > in the Leslie Sim itself. We didn't add anything like that.
> > >
> > > Regards,
> > >
> > > Jerry
> >
> > No, the new "Noise" parameter was and still is set to "0".
> > This noise is unaffected by "Wheel
Type","Leakage","Overtone","Horn
> > Mic Dist.","Rotor Mic Dist." or anything else I've tried. The
only
> > things I've found that affect it are "Speaker Sim=On" to lessen
it
> > or "Amp Type=Preamp" to return to a silky silence. It's almost
as
> if
> > v1 had a noise gate at the end of the Leslie sim chain and in
v2,
> > it's been turned off.
> >
> > When the new v2 loader gets posted again, will there also be a
post
> > allowing me to go back to v1 (at my own risk of course) to
verify
> > that I'm not just imagining this?
>
> To unsubscribe, send email to: CloneWheel-unsubscribe@y...
>
> Your use of Yahoo! Groups is subject to the Yahoo!
> Terms of Service.
>
> [Non-text portions of this message have been removed]